Cedar Summit F25650 Operations Instructions

INSTALLATION AND OPERATING INSTRUCTIONSM O U N T F O R E S T L O D G E – F 2 5 6 5 0To reduce the risk of serious injury or death, you must re

Nominal Size1" x 4"1" x 5"1" x 6"Actual Size⅝" x 3¼"⅝" x 4¼"⅝" x 5¼"Part Identification (R

Step 31: Attach Swing End Ground StakesOther PartsA: In the 2 places shown in g. 31.1 drive the Rebar Ground Stakes 13” into the ground against the

Step 32: Clock Roof Assembly Part 1A: Attach 1 (320) Small Roof Support to a second (320) Small Roof Support at peak using 1 (S3) #8 x 2-1/2” Wood S

Step 32: Clock Roof Assembly Part 2C: Place Small Roof Support Assembly on (040) Cafe Wall Window Panel centred over the Clock so the bottom of the

Step 33: Attach Sand and Water Table to FortOther PartsA: Centre Sand and Water Table from Step 1 between the two bolts on the bottom of (040) Cafe W

Step 34: Attach Slide to FortNote: Pre-drill all holes using a 1/8” drill bit before installing the pan screws.A: Place Slide centred in the opening

Step 35: Attach Access Ladder Rockwall AssemblyHardwarePre-drill all holes using a 1/8” drill bit before installing the Wafer LagsA: Remove (030) B

Step 36: Attach Steel Hand Grips to FortHardwarePre-drill all holes using a 1/8” drill bit before installing the Wafer LagsA: Measure 6” from the t

Step 37: Attach Middle Arch to FortHardwareA: Measure 28” from the top of (025) Top Ladder on each (050) Narrow Window Panel and attach (370) Middl

Final Step: Attach I.D. Plaque Other Parts1 x I.D. Plaque - Cedar Summit 4 x #6 x 5/8” Pan ScrewHardwareS13I.D. Plaque - Cedar SummitA: Attach I.D

NOTES 109 [email protected]

2pc. -034 - Rock Board C FSC 1 x 6 x 20½" - Box 5 - 46388242pc. -012 - Box Ground FSC 5/4 x 4 x 29" - Box 2 - 46388301pc. -190 - Right G

NOTES 110 [email protected]

NOTES 111 [email protected]

CEDAR SUMMIT Consumer Registration CardFirst Name Initial Last NameStreet Apt. No.City State/Province ZIP/Postal CodeCountry Telephone NumberE-M

Part Identification (Reduced Part Size) Actual Size15/16" x 3¼"15/16" x 4¼"15/16" x 5¼"Nominal Size5/4" x 4"5/

124 - Short Floor Joist FSC 2 x 4 x 5¼" - Box 4 - 46386231pc. - - Small Roof Support FSC 2 x 2 x 22½" - Box 2 - 4638802320-2pc. 2pc. -121 -

1pc. -271 - Block SW FSC 2½ x 3 x 15" - Box 3 - 46385071pc. - Part Identification (Reduced Part Size)2603 x 33" x 5¼"1¼" x 5"

1pc.- Part Identification (Reduced Assembly Size)-Transom Panel Front FSC 1¼ x 11½ x 35⅞" - Box 2 - 47638745220 2pc. - Box 4 - 47638749 FSC 1¼ x

1x - EN71 Hand Rail (9200223) -Yellow1x - Telescope (3320161) 1x. - Rocks (10pk) (3320210) -Green/Yellow/Burgundy1x - Spin Chalk Sign (332071

2pc. -G1 -Hex Bolt 5/16 x 1-1/2" - (53703312) 1pc. -D4 -#2 x 2" Robertson Driver Bit- (9200014)20pc. -WB9 -Wafer Bolt 5/16 x 2⅛"

14pc. -S10 -Pan Screw #8 x 1" - (52433510)55pc. -S15 -Wood Screw #8 x 1¾" - (52043513)28pc. -S4 -Wood Screw #8 x 3" - (5204353

14pc. FW0 -3/16" Flat Washer - (51103100) 10pc. LW1 - 1/4" Lock Washer - (51303200) Hardware Identification (Actual Size)Accessory Ide

Warnings and Safe Play InstructionsCONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while

[email protected]. If there are any missing or damaged pieces or you need assistance with assembly please contact the consu

A: Loosely attach 1 (011) Box End to 2 (010) Box Legs using 2 (WB2) 5/16 x 1-3/8” Wafer Bolts (with at washer and t-nut), as shown in g. 1.1 and 1.

D: With assistance from another adult, place 2 (013) Box Sides on the notched out edges of the (010) Box Legs so they are ush to the outside edges o

2 x Box Gusset FSC 5/4 x 4 x 8-1/2”014Wood Parts2 x #8 x 1-3/4” Wood Screw4 x #8 x 2-1/2” Wood Screw2 x #8 x 1-3/8” Wood ScrewHardwareS3Fig. 1.7Fi

I: Turn the Table Assembly right side up.J: Place the Sand and Water Insert into the opening of the assembly then tighten all the bolts. (g. 1.9)K:

1 x Left Access Rail FSC 2 x 4 x 62-7/8”1 x Right Access Rail FSC 2 x 4 x 62-7/8”4 x Ladder Tread FSC 5/4 x 4 x 13-3/4”022021020Fig. 2.1Wood Parts

1 x Ladder Gap FSC 1 x 4 x 15”1 x Rock Rail FSC 2 x 4 x 62-7/8”1 x Top Ladder FSC 5/4 x 3 x 34-1/4”Fig. 2.5Fig. 2.6Swing Bracket024025023Step 2:

1 x Board Access FSC 1 x 4 x 20-1/2”1 x Rock Bottom FSC 1 x 6 x 20-1/2”3 x Rock Board A FSC 1 x 6 x 20-1/2”3 x Rock Board B FSC 1 x 6 x 20-1/2”Ste

Step 3: Rockwall Assembly Part 210 x 1/4 x 1-1/4 Pan Bolt  (1/4”lockwasher,3/16”atwasher&1/4”barrelnut)10 x #8 x 1” Pan ScrewPB2Ha

Step 4: Panel Preparation Part 1HardwareA: On the outside of (040) Cafe Wall Window Panel place 2 (041) Window Shutters on each side of both windows

One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under

Step 4: Panel Preparation Part 2Hardware4 x #8 x 1” Pan ScrewOther Parts1 x Clock AssemblyS10C: Place the Clock on (040) Cafe Wall Window Panel lin

Step 4: Panel Preparation Part 3HardwareE: From the back of (042) Chalkwall Panel place the Spin Chalk Sign in the opening so it sits tight to the p

Step 4: Panel Preparation Part 4HardwareG: Place (044) SW Wall at the top of the front of (043) SW Side Panel and attach with 4 (G21) 5/16 x 3-3/4”

1 x Narrow Window Panel FSC 1-1/4 x 16-3/4 x 99”Wood Parts Hardware Other Parts2 x 2 x 2-1/4” Corner Panel Bracket0504 x #12 x 3/4” Pan ScrewS8St

1 x SL Side Window Panel FSC 1-1/4 x 30 x 54-1/8”Wood Parts HardwareOther Parts2 x 1-1/2 x 2-1/4” Corner Panel Bracket0514 x #12 x 3/4” Pan Screw

Hardware4 x #12 x 3/4” Pan ScrewStep 5: Swing Side Panel Assembly Part 3E: Lay (043) SW Side Panel from Step 4, Part 4 on the ground, then with a h

Step 5: Swing Side Panel Assembly Part 4Hardware6 x 1/4 x 2-1/2” Wafer LagWL5G: With a helper hold (051) SL Side Window Panel up against the left s

A: Place 1 (042) Chalkwall Panel from Step 4, Part 3 on the ground. Measure 3-1/4” up from the bottom of the panel on the left side and attach a 1-1

1 x Half Narrow Window Panel FSC 1-1/4 x 16-3/4 x 56”Wood Parts Hardware Other Parts2 x 2 x 2-1/4” Corner Panel Bracket0604 x #12 x 3/4” Pan Scr

1 x Door Wall Window Panel FSC 1-1/4 x 36 x 54-1/8”Wood Parts061Hardware8 x #12 x 3/4” Pan ScrewS8Step 6: Door Wall Assembly Part 3E: Lay (061) Do

Instructions for Proper MaintenanceYour Cedar Summit Play System is designed and constructed of quality materials with your child’s safety in mind. As

6 x 1/4 x 2-1/2” Wafer LagHardwareWL5Note: Make sure panels are square and ush to each other. (g. 6.9)H: Pre-drill with a 3/16” drill bit, then fa

1 x Front Floor FSC 2 x 4 x 81”1 x Front Ground FSC 5/4 x 4 x 79-3/4”1 x Back Floor FSC 2 x 4 x 81”1 x Back Ground FSC 5/4 x 4 x 79-3/4”I: Insta

4 x 5/16 x 2-3/8” Wafer Bolt (5/16”atwasher)4 x 5/16 x 2-1/8” Wafer Bolt (5/16”atwasher)HardwareWB9K: Starting at the bottom of the Door Wa

A: With at least two helpers lift the Door Wall Assembly, as shown in g. 7.1 and 7.2.B: With at least two helpers lift the Swing Side Wall Assembly

C: Loosely attach (063) Front Ground and (065) Back Ground to (051) SL Side Window Panel and (050) Narrow Window Panel with 2 (WB9) 5/16 x 2-1/8” Waf

HardwareStep 8: Front Wall Assembly Part 1Fig. 8.3Fig. 8.1A: Fit (040) Cafe Wall Window Panel, from Step 4, in between (051) SL Side Window Panel an

Fig. 8.4062Step 8: Front Wall Assembly Part 2C: Make sure the assembly is on level ground and (051) SL Side Window Panel and (042) Chalkwall Panel a

Other Parts2 x Flat Panel BracketStep 8: Front Wall Assembly Part 3E: On the outside of the assembly place (080) Table Top in the opening of (040) C

Step 8: Front Wall Assembly Part 4H: Attach (043) SW Side Panel to (062) Front Floor and to (064) Back Floor with 2 (S4) #8 x 3” Wood Screws per sid

Hardware Other Parts1 x Door Handle1 x Catch PlateStep 9: Door Wall Assembly Part 1A: On the inside of (090) Door Window Panel, measure 16” up from

About Our WoodCedar Summit Premium Play Systems uses 100% FSC wood. Although we take great care in selecting the best quality lumber available, wood i

Fig. 9.3Fig. 9.4090S13S13Outside View1/2”Hinge StopHardwareStep 9: Door Wall Assembly Part 2C: On the outside of the (090) Door Window Panel attach

061Fig. 9.7HardwareStep 9: Door Wall Assembly Part 3E: In the opening for the door, measure 5/8” from the top of Door Wall Window Panel bottom and m

Fig. 9.10HardwareWood PartsStep 9: Door Wall Assembly Part 4F: In the notched out opening of (091) Door Stop attach the Magnetic Catch using 2 (S18)

1 x Floor End FSC 5/4 x 6 x 38-1/2”1 x Door Bottom FSC 1 x 4 x 33-1/2”Wood Parts0928 x #8 x 1-3/8” Wood Screw4 x #8 x 3” Wood ScrewHardwareS20St

HardwareFig. 10.10606x 5/16x2-1/8”WaferBolt(5/16”atwasher,4x5/16”t-nut)2x 5/16x2-3/8”WaferBolt(5/16”atwasher)Step 10: Back Wa

Fig. 10.5Step 10: Back Wall Assembly Part 2C: Make sure the assembly is square. D: Tighten all 16 Wafer Bolts on the back side as shown in g. 10.

4 x #12 x 3/4” Pan ScrewHardware1 x Flat Panel BracketOther PartsS8Fig. 10.6Step 10: Back Wall Assembly Part 3E: On the inside of the assembly atta

Step 11: Swing Wall Assembly Part 1Wood PartsHardwareKeep all bolts loose in this step.A: Loosely attach (110) Ground SW to the bottom of (043) SW S

Step 11: Swing Wall Assembly Part 2C: Pre-drill pilot holes with a 3/16” drill bit then attach (111) Diagonal to (050) Narrow Window Panel and (060)

HardwareWood Parts1 x SL Top Left FSC 5/4 x 5 x 9-3/4”2 x Short Joist FSC 2 x 4 x 5-1/4”2 x Post FSC 5/4 x 4 x 31-7/8”1 x SL Top Right FSC 5/4 x 5

and quantities required to complete the assembly step illustrated on that page. Here is a sample.Key Number:represent the step number. The third digit

Hardware1 x Short Floor Joist FSC 2 x 4 x 5-1/4”Wood Parts124Fig. 12.3082C: Place Left Side Post Assembly tight to (043) SW Side Panel and (082) SL

HardwareE: Make sure (120) SL Top Left is ush to the inside edge of the panel support then attach to (043) SW Side Panel and attach (123) SL Top Rig

4 x #8 x 2-1/2” Wood Screw6 x #8 x 3” Wood ScrewHardware1 x SL Top FSC 5/4 x 5 x 30-5/8”1 x SL End FSC 2 x 4 x 28-3/4”Wood Parts125G: Flush to th

1 x Front Top FSC 5/4 x 4 x 65-1/2”Wood Parts127Hardware1 x #8 x 1-3/4” Wood Screw2x 5/16x2-1/8”WaferBolt(5/16”atwasher,5/16”t-nut)S15I

Warning! To prevent tipping and avoid potential injury,stakesmustbedriven13”intoground.Diggingordrivingstakescanbedangerousifyoudono

HardwareWood PartsStep 14: Attach Floor JoistA: With one person inside the assembly line (140) Floor Joist up to the pilot holes on the (092) Floor

Hardware3 x Slidenest Floor FSC 1 x 6 x 42-1/2”3 x Slidenest Floor A FSC 1 x 5 x 42-1/2”Wood Parts15048 x #8 x 1-3/8” Wood ScrewS20Step 15: Floor

9 x Floor FSC 1 x 6 x 36”1 x Floor A FSC 1 x 5 x 36”Wood Parts152092D: Next to (151) Slidenest Floor A place 9 (152) Floors followed by 1 (153) Flo

A: Loosely attach (160) Crowsnest Top ush to the top of 2 (161) Crowsnest Posts, noticing the bolt holes are at the top, with 2 (WB7) 5/16 x 3” Wafe

C: Tight to the top of (042) Chalkwall Panel place 1 (163) Crowsnest Bottom in between (040) Cafe Wall Window Panel and (092) Floor End on the front

Key Number: The rst two digits represent the step number. The third digit represents the order in which the part is listed in the step. Note that if

E: Place Crowsnest Frame Assembly from Step 16, Part 1 on the fort so the (161) Crowsnest Posts are tight to (092) Floor End and (163) Crowsnest Bott

HardwareFig. 16.82 x #8 x 2-1/2” Wood Screw6 x #8 x 1-3/8” Wood Screw1 x Centre Wall Board FSC 1 x 5 x 32”1 x Steering Wheel Dash FSC 5/4 x 5 x 12

Wood PartsK: Measure 2-3/4” from each (161) Crowsnest Post and attach 2 (166) Wall Boards to (160) Crowsnest Top and (092) Floor End, tight to (153)

Step 16: Crowsnest Assembly Part 6M: Measure 2-5/8” from both (161) Crowsnest Posts and attach 1 (166) Wall Board per side to (162) Crowsnest Sides

Hardware Other Parts1 x 1/4 x 2-1/2” Wafer Lag (5/16”atwasher)Step 17: Attach Steering Wheel and TelescopeA: Pre-drill with a 1/8” drill bit, t

Wood PartsHardwareFig. 18.11 x Roof Support FSC 5/4 x 4 x 29”1 x Roof Support Left FSC 5/4 x 4 x 29”1 x Top Post Right FSC 1-1/4 x 2-1/8 x 24-5/8”1

Wood Parts1 x Sunburst FSC 5/4 x 6 x 10”185Step 18: Roof Support Assembly Part 2D: Place Roof Support Assembly on the ground with the front facing

HardwareStep 18: Roof Support Assembly Part 3E: Place (186) Centre Gable on (185) Sunburst, tight to the top of (184) SW Top so the tip is centred a

Wood PartsHardware1 x Right Gable Angle FSC 5/4 x 4 x 31”1 x Left Gable Angle FSC 5/4 x 4 x 31”1 x Gable Bottom FSC 2 x 4 x 34-1/2”192191190Step 19

Notice bolt side facing out.Wood Parts1 x Sunburst FSC 5/4 x 6 x 10”185D: Measure 8-1/2” from the centre of either bolt hole then place 1 (185) Sunb

Acro Bar183125PARTSI DENTIFICATIONFRONT051 SL Side Window Panel153181185186x4187182270Panel SW Side 043120025x2042Sign184Clock ChalkWall PanelSpin18

HardwareE: Place (186) Centre Gable on (185) Sunburst, tight to the top of (192) Gable Bottom so the tip is centred at the peak of the Gable Angle Su

Wood PartsHardwareFig. 20.12 x Roof Spacer FSC 5/4 x 6 x 32-1/4”2001 x #8 x 3” Wood ScrewS4Step 20: Roof Spacer AssemblyA: Attach 1 (200) Roof Spa

HardwareA: Connect 1 (210) Large Roof Panel to a second (210) Large Roof Panel so the one panel overlaps the other and the inside angle is square and

HardwareStep 21: Small and Large Roof Assemblies Part 2B: Connect 1 (211) Small Roof Panel to a second (211) Small Roof Panel so the one panel overl

HardwareC: Place Roof Spacer Assembly from Step 20, on top of the Small Roof Assembly, ush to the edge as shown in g. 21.5. D: Measure 1/2” in

Fig. 22.1Step 22: Attach Transom Front and Back Part 1A: If the space is too tight loosen the bolt at the front of the assembly, as shown in g. 22.

Step 22: Attach Transom Front and Back Part 2C: Place (221) Transom Panel Back on top of (050) Narrow Window Panel, behind (100) Back Top so the out

HardwareA: Place Roof Support Assembly, from Step 18, Part 3, on the top of (043) SW Side Panel, ush to the front. (g. 23.1 and 23.2)B: Attach (1

HardwareD: Make sure the distance between (040) Cafe Wall Window Panel and (050) Narrow Window Panel is 36”. (g. 23.3 and 23.4)E: On the Door Wall

HardwareF: From inside the assembly attach (190) Right Gable Angle to (050) Narrow Window Panel and (191) Left Gable Angle to (040) Cafe Wall Window

Window Panel Door Wall 061Window Panel DoorBench Set3 in 1 090REARPARTSI DENTIFICATION Wall Window Panel Half Narrow0602Window Panel X Narrow 0502

A: With 2 people on the ground and at least 1 person in the fort, lift the Small Roof Assembly with Roof Spacer Assembly, from Step 21, Part 3, up an

C: Make sure the Small Roof Assembly lays at on the Gable Angle Support Assembly and it overhangs by 2”. (g. 24.2 and 24.3)D: Measure 3/4” from t

E: With 2 people on the ground and at least 1 person in the fort, lift the Large Roof Assembly, from Step 21, Part 1, up and over the Back side of th

g ppHardwareStep 25: Attach Heavy T-Bracket to FortA: Attach Heavy T-Bracket to (044) SW Wall using 2 (WB7) 5/16 x 3” Wafer Bolts (with at washer a

Step 26: Swing Beam AssemblyHardwareA: Attach 6 Heavy Duty Swing Hangers to (260) Engineered SW Beam using 2 (G13) 5/16 x 6-1/8” Hex Bolt (with 2 a

1 x SW Block Angle FSC 2-1/2 x 3 x 15”1 x Block SW FSC 2-1/2 x 3 x 15”2 x SW Post FSC 4 x 4 x 105”Step 27: Swing Post Assembly Part 1272271270Not

g pp4 x #6 x 1” Wood Screw1 x 3/8 x 4” Hex Bolt (3/8”atwasherx2&3/8”locknut)Step 27: Swing Post Assembly Part 2D: Attach Cedar Summ

Step 28: Attach Cross SupportHardwareWood PartsPre-drill all holes using a 3/16” drill bit before installing the lag screws.A: Check to make sure the

Step 29: Final Swing Post AssemblyHardwarePre-drill all holes using a 3/16” drill bit before installing the lag screws.Note: Tighten all bolts from

Step 30: Attach SwingsOther PartsA: Using 1 Threaded Clip per chain, join 1 Long Swing Chain to each side of the swing belt seat. Make sure to clos